Søk
    Totalt
    Vis handlekurv
    CRP dehumidifiers from HBC
    files/importert/Produkter/Bilder/CRP_heading.jpg
    The CRP dehumidifier series is designed for process air drying, ie. applications of low dew points or deep drying.
    For this application the dehumidifier often is connected a pre- and/or post cooler. Process drying needs very reliable equipment, and due to the special high quality components used in the CRP series, this high reliability isachieved. The CRP series dehumidifiers is the top-quality process dehumidifiers.
     
    THE CRP DEHUMIDIFIER FEATURES
    • Cabinet manufactured in stainless steel
    • Designed for low dew point applications
    • Designed for easy connection of external AHU parts
    • The insulated inlet plenum allows for pre-cooled process air
    • Electronic controller for stepless temperature control (reg.air)
    • External pressure available for dry air and reg.air for ducting on site
    • Pocket filters for process air inlet, filter cassette for reg.air inlet
    • Internal components of highest quality and reliability
    • High performance desiccant rotor of washable silica gel
    • Separated air flows for process air and for reg.air, two fans installed
    • Easy access for service and maintenance
    • Electric-, steam-, or gas heater available.

     AREAS OF APPLICATION
    The CRP range is designed for process drying. Process drying is often a process of drying fresh
    air to a low dew point, a process that often needs a pre- cooler for the first dehumidification step,
    then the CRP dehumidifier for the low dew point, and finally a post cooler for the temperature
    control of the dry air. A combination of standard AHU components connected our standard CRP
    dehumidifier, ensures the highest quality of the critical part: the dehumidifier.

    CONTROLS
    our electronic hygrostats DA20 and
    DH24 or our
    For controlling the CRP series dehumidifiers we recommend
    advanced microprocessor based Dehumidifier Control Centre, DCC.
    The DCC controls the dehumidifier on %RH and/or dew point.
    Internal alarms and temperatures of the dehumidifier can be displayed, aswell as the control
    parameters can be setup in the DCC remote panel. External values of temperature, %RH and
    dew point for up to 3 sensors can be displayed. The DCC offers on/off and stepless control of the
    dehumidifier, allthough the CRP series dehumidifiers needs an optional component in order to use
    the stepless control.

    TECHNICAL DATA

     

    Type

    Dry air

    nominel

     

    m3/h

    Reg.air

    nominel

     

    m3/h

    Supply

     

     

    V/faser

    Connect.

    power

     

    kW

    Fans

     

     

    kW

    External

    protection

    A

    Capacity at 20C, 50 %RF

    Kg/h

    CRP2000

    2000

    650

    400/3Ph PE

    25

    3,3

    35

    14

    CRP2500

    2500

    750

    400/3Ph PE

    29

    3,3

    50

    17

    CRP4000

    4000

    1300

    400/3Ph PE

    49

    4,1

    80

    27

    CRP6000

    6000

    1950

    400/3Ph PE

    65

    5,5

    100

    41

    CRP8000

    8000

    2400

    400/3Ph PE

    91

    7,0

    160

    55

    CRP12000

    12000

    3800

    400/3Ph PE

    149

    14

    250

    87

    CRP18000

    18000

    5400

    400/3Ph PE

    208

    19

    315

    130

    CRP25000

    25000

    7600

    400/3Ph PE

    294

    24

    200 250

    180

    CRP30000

    30000

    9000

    400/3Ph PE

    348

    33

    250 315

    212

     

     

     

    CRT dehumidifiers
    files/importert/Produkter/Bilder/crt-heading.jpg
    The CRT dehumidifier series is designed for Room Air Drying, ie. applications of high water removal, kg/h. The design principle is "high air flow / high water removal”, which makes the process highly economical. The process air flow can even be increased above the nominal value, which is important at process air inlets of low %RH and/or low temperatures. The CRT series is the top quality dehumidifiers for Room Air Drying.
     
    THE CRT DEHUMIDIFIER FEATURES
      • Cabinet manufactured in stainless steel 
      • Designed for high air flow and high capacity, kg/h
      • Designed for easy connection of external AHU parts
      • The insulated inlet plenum allows for pre-cooled process air
      • Electronic controller for stepless temperature control (reg.air)
      • External pressure available for dry air and reg.air for ducting on site
      • Pocket filters for process air inlet, filter cassette for reg.air inlet and choice of internal components of highest quality and reliability
      • High performance desiccant rotor of washable silica gel
      • Easy access for service and maintenance
      • Electric-, steam- or gas heater

    UNIVERSAL APPLICATION

    • Dry air storage (Moisture control in unheated storage rooms)
    • In museums and Military magazines
    • Industrial installations
    • Garages & hangars
    • Corrosion protection of steel and steel constructions ie. bridges etc.
    • Cold stores and freezers
    • Reduction of ice on evaporator, on ceiling, at doors
    • Protection of electronics, tanks, fighters in military installations
    • Production and store room for low %RH in medical and food industry
    • Water work buildings, also with open water surfaces
    • Ice skating rinks
       
    CONTROLS
    Our electronic hygrostats DA20 and DH24 or our For controlling the CRT series dehumidifiers we recommend advanced microprocessor based Dehumidifier Control Centre, DCC. The DCC controls the dehumidifier on %RH and/or dew point. Internal alarms and temperatures of the dehumidifier can be displayed, aswell as the control parameters can be setup in the DCC remote panel. External values of temperature, %RH and dew point for up to 3 sensors can be displayed. The DCC offers on/off and stepless control of the dehumidifier, allthough the CRT series dehumidifiers needs an optional component in order to use the stepless control. CONTROLS.
    ype Process air flow,
    m³/h
    Reg.air flow,
    m³/h

    Voltage
    V

    Capacity at 20°C/50% RH
    Kg/h
    Power
    consumption
    KW
    Weight
    Kg
    CRT3000 3000 680 400 18 25 550
    CRT6000 6000 1300 400 35 50 700
    CRT9000 9000 1900 400 51 69 850
    CRT12000 12000 2600 400 69 93 1200
    CRT18000 18000 3600 400 101 149 1400
    CRT22500 22500 4500 400 127 193 2000

     

    F-DRY CR240B Adsorption dryer
    files/importert/F-DRY/Bilder/CR240B.jpg

    GENERAL

    Drying Capacity:
    At 20 ° C / 60%r.h. = 20,0 kg/day

    Air flow and pressure: 
    Dry air, free blowing : 320 m3/h
    Dry air, nominal : 240 m3/t
    Reg. air, nominal: 40 m3/t

    External pressure, dry air (at 240 m3/h): 80Pa
    External pressure, reg. air (at 40 m3/h): 120Pa

    Control and signals
    On- / Off- rotary switch  (Auto - 0 - Man)
    Ammeter to control the reg. air flow.
    Operation time counter
    Outside socket connector for Hygrostat

    Housing:
    Rugged construction of stainless steel.
    Easy access for service and repair

    Technology:
    The process air moves through the continuously turning rotor. The rotor includes the moisture of air. A stream of air which flows into opposite direction is heated up by a PTC-heater. This hot air evaporates the water from the rotor and leaves the unit and the room as warm and wet reg.-air. Common fan for both streams.

    The Rotor:
    The rotor is made of min. 82% Silicagel, which is laced chemically and not solvably to a base of glass fiber. An impregnation is not required. The regeneration temperature of the rotor is with approx. 120-140°C..

     
    ELECTRICAL CONNECTION:

    Voltage 
    1 x 230 V / 50/60 Hz, connecting cable: 2 mtr. with Schuko coupler

    Fusing:
    10 Amp.

    Power consumption:
    PTC - heater: 920kW
    Fan: 130W
    Total consumtion: 1,060W

    Installation and dimensions:

    Deployment/mobility 
    4 rubber dampers
    Easy to carry with the handle on the top of the unit

    Air intake:
    Commn intake for process air and reg. air.  

    Air output:
    Dry air : Ø100mm connection (spiro).
    Reg. air: Ø80mm connection (spiro)

    Use of the unit:
    Coupler into the socket. Turn on device on the rotary switch. Adjust the air volumes in accordance with operating manual and display on the ammeter. Lead regeneration exhaust hose (accessory) from the room.

    Dimensions:
    length / width / height:, cabinet: 395 mm/ 330 mm/ 335 mm
    length / width / height:, total: 475 mm/ 335 mm/ 360 mm 

    Weight:
    15 kg

    Service:
    Change filter, check rotor belt

    Har du spørsmål om produktet?